| Make | Model | Problem | Solution | Date |
| | | |
| Found: 143
|
| Mitsubishi | Euro 10 CT2525TX | Field collapse | no 12v to pin 3 of frame Ic due to o/c corroded print from leaky cap. | 14-09-04 |
| Mitsubishi | CT25A5STX Euro 14SF | Field collapse | Z551 SOC3150 o/c, D553 BYD33G s/c, IC5E1 TEA2031 EW corr chip s/c pins 5 & 6, L555 15µH shorted turns | 14-09-04 |
|
|
| Mitsubishi | CT25A5STX Euro 14SF | Field collapse & Z551 cct prot o/c | IC5E1 TEA2031A on E/W module s/c due to L555 E/W loading coil s/c turns SEME pt no TPAR2343 | 14-09-04 |
| Mitsubishi | CT25A5STX Euro 14SF | Field collapse with E-W fault when FOP chip replaced | Replace TEA2031A FOP chip & L555 - which caused chips demise | 14-09-04 |
| Mitsubishi | CT25M3TX Euro 14 | Difficult to come on from st/by, wont stop at stations & graphics wrong | C955 2200µ 25v leaked over EEPROM IC702 X24CO4P - both need replacing | 14-09-04 |
| Mitsubishi | CT25M3TX Euro 14 | Tuning instructions | Select chan & press preset on r/c (tuning display appears in blue at bottom of display), change to yellow by pressing up/down chan. press vol +/- to start search tune, then press vol + until channel is displayed, press preset button to store | 14-09-04 |
| Mitsubishi | CT29A4STX Euro 12 | Buzz from spkrs in st/by | C960 1000µ 50v | 14-09-04 |
| Mitsubishi | CT29A4STX Euro 12 | Int NICAM Beacon on screen &/or buzz or hiss on sound | Dry joints IF can - L9 & pins 20-24 of IC2 | 14-09-04 |
| Mitsubishi | CT29B2STX Euro 11 | Int goes to st/by | Print damage in BCL cct near conn between SCART sub panel & main PCB - The damaged track connects D551 near LOPT and R206 near pin9 IC201 MC44000. You will need to take the PCB out as this place is hidden under the plastic chassis. | 14-09-04 |
| Mitsubishi | Euro 1 | Diagonal pattern of dots across screen | R914 100R in psu snubber cct o/c | 14-09-04 |
| Mitsubishi | Euro 10 | Black lines , poor sync, no txt (until warm) | C959, 962 100µ | 14-09-04 |
| Mitsubishi | Euro 10 | Dead | C905 470µ 25v | 14-09-04 |
| Mitsubishi | Euro 10 | Dead - Q901 chopper tr blows at sw on | D909 3v zener s/c was the cause; also replaced R901 4R7 5w, IC901 TEA2164 | 14-09-04 |
| Mitsubishi | Euro 10 | dead psu runs | several electrolytics in psu leak electrolyte onto plug PB causing o/cs | 14-09-04 |
| Mitsubishi | Euro 10 | Field jitter - int | Dry joint R461 | 14-09-04 |
| Mitsubishi | Euro 10 | Field lin faulty when cold | Glue around pins of IC501 | 14-09-04 |
| Mitsubishi | Euro 10 | HT low | Q953 JC501Q error amp | 14-09-04 |
| Mitsubishi | Euro 10 | int dead (could be ok for days) | Same on dummy load proving psu fault. Opto coupler driver tr Q953 was to blame. BC547 suitable replacement | 14-09-04 |
| Mitsubishi | Euro 10 | Int dead esp from cold | C905 220µ, C906 47µ C912 4µ7 in psu | 14-09-04 |
| Mitsubishi | Euro 10 | Int loss of sound & pic | Check vid I/p & o/p at AV sw chip IC2A2 M5132P - if no o/p either off air or scart this chip is sus; if o/p with scart but not off air sus Q2A2. If no pic but sound ok check Q104 | 14-09-04 |
| Mitsubishi | Euro 10 | Int sw on from cold | C905 470µ 25v in start up cct | 14-09-04 |
| Mitsubishi | Euro 10 | Loses analogue memory when sw off | The -30v to IC702 memory chip low due to C962 100µ 50v | 14-09-04 |
|
|
| Mitsubishi | Euro 10 | Loud whistle from psu - set operates ok otherwise | Q902 | 14-09-04 |
| Mitsubishi | Euro 10 | No pic - OSG & sound ok | No 5v reg supply to VIP & CCT chips as Z951 630mA cct prot o/c | 14-09-04 |
| Mitsubishi | Euro 10 | No sound | Q952 2SA950-Y leaky | 14-09-04 |
| Mitsubishi | Euro 10 | No sound | No lt supply to audio chip - Q952 2SA950 o/c; BC640 used in lieu | 14-09-04 |
| Mitsubishi | Euro 10 | No sound | Z952 cct prot SOC2000 in psu o/c. When replaced sound ok thro' SCART but none at RF - no sound o/p from IF chip IC101 due to L301 det coil | 14-09-04 |
| Mitsubishi | Euro 10 | No sound/pic - no memory & slow R/C response | IC702 EEPROM chip ST24C02A | 14-09-04 |
| Mitsubishi | Euro 10 | not memorising user prefs | C962 100µ on -30v supply | 14-09-04 |
| Mitsubishi | Euro 10 | Patterning - clears with a bang on cabinet | IC902 12v reg faulty | 14-09-04 |